Isogam is a durable coating and moisture insulation that is implemented for moisture penetration on any surface. Isogam insulation is made up of bitumen, t -fibers, polyester fibers, sometimes aluminum foil and other polymer materials, the most important of which is the most important ingredient. The isogam is executed and glued by heat in the desired location.
This material is available as 1 m wide and 10 m in length about 4 mm thick in single and two layers, pure or blossom bitumen, simple or aluminum coating in the market. Two -layer rolls have two strata of Tisho and polyester fibers to maintain and arm the bitumen layer. The average weight of each isogam roll is about 40 kg.
The sample containing pure bitumen has a higher durability and quality than the blows. Aluminum covering rolls are also suitable for roof due to light reflection, prevention of insulation warming in summer and a positive effect on snowfall water.
generally use isogam in moisture insulation for places such as roof, Pools, walls and walls and any surface that should not penetrate moisture can be used. Other important information you need to know about isogam insulation is its useful life. If the isogam is of a quality type and is well implemented, it has an average life of 10 to 15 years.
The main reasons for using isogam as a moisture insulation can be high speeds, no need to create fire to soften bitumen and low environmental pollution.
How and methods of implementation of isogam
The way and how the isogam runs for any part of the building to be implemented follows a fixed process. Generally, a few steps should be done in the installation of the isogam in order to ultimately be good quality.
In this section, we examine and explain how to execute the isogam.
1) sloping surface
Since the purpose of the isogam is to prevent moisture from penetrating the lower surface, if the slope is not done properly, the water remains at one point and over time will find a way to penetrate the surface.
Therefore, the important point in water -related flooring is the principle of slope. The principle of roof sloping and other building spaces is one of the most important tasks before the implementation of bitumen and isogam. We have talked about this in the roof sloping article. Click the blue link to read it.
In fact, the sloping should be done so that water is not accumulated on the surface. Of course, it is best to install one or two layers of isogam before installing the original isogam to prevent possible water penetration in places such as around the gutter, honor wells, and under the coolers.
2) Infrastructure
If it is to work on the surfaces where the flooring is implemented, proper infrastructure should be done. For example, if the surface is mosaic, it should first be poured on the surface and then used in the oil solvent derivative. Or, if the cement level is a cementitious work, the oil -soluble -soluble -soluble -soluble derivative is used.
because the isogam is able to break the corner, the wall of the floor and the wall of the muscle will be hit before the isogam.
3) Taking seams and gaps
Since any seam and cracking below the isogam surface can cause fractures and cracking it, it is necessary for the surface to be completely uniform and free of any seams. Materials such as sand, cement, mineral shell or other filling materials can be used to fill the seams and gaps. The purpose of this step is to better attach the isogam to the surface.
4) Cleaning the surface
Next, the surface on which the insulation is to be done should be completely cleaned with water and vacuum cleaner so that no dust and contamination remain on the surface. This step is of great importance for installing isogam and we need to do it well.
You must also have all the objects on the surface such as water source, air conditioner, etc. to run the isogam freely and freely. Do not be done without annoying objects.
5) Prepare isogam roll
Now that the surface is ready to be an isogam, we first open the isogam rolls and remove the plastic layer on the surface. If the rolls were high, the torch is used to open the rolls and prevent them from tearing.
6) Installation of isogam
Installation and glue isogam is the last step of its implementation. At this point, after opening the isogam roll and cutting it according to the surface that is supposed to be isogam, we stick the isogam layers using flame heat.
At this point, it is necessary to smooth the isogam layer on both sides so that it does not create wrinkles and extra air while sticking to the surface. The way the isogam is executed is that both layers that follow each other should overlap and connect well to each other using flame heat.
Ensure that the isogam layer is well on the surface. Attached is also a significant point that should not be overlooked.